Cardone Ultra 18-P4196 Disc Brake Caliper For FORD,MAZDA

Buy Part Now

ShowMeTheParts has a wide selection of Cardone Ultra products for a variety of years, makes, and models.

Cardone Ultra 18-P4196 Disc Brake Caliper For FORD,MAZDA

BUYERS GUIDE

Make Model Year Engine
FORDAEROSTAR1987-97All
FORDBRONCO II1984-85All
FORDBRONCO II1987-90All
FORDEXPLORER1991-94All
FORDRANGER1983-85All
FORDRANGER1987-94All
MAZDAB23001994All
MAZDAB30001994All
MAZDAB40001994All
MAZDANAVAJO1991-94All

PART INFORMATION

Brand:Disc Brake Caliper by Cardone Ultra For FORD,MAZDA | ShowMeTheParts.com
Part Number:18p4196
Part Type: Disc Brake Caliper
Comment:Expertly remanufactured to rigorous quality and performance standards, all CARDONE Ultra Premium Calipers are equipped with brand-new, premium components to guarantee exceptional longevity and reliability. The exclusive weather-proof silver coating effectively prevents rust and corrosion, lengthening product life and maintaining a premium appearance. All brake calipers are 100% pressure-tested to deliver consistent, industry-leading braking performance. Each unit arrives with a complete set of brand-new hardware for a simple, complete installation. Caliper bracket is included when applicable.

PARTS ATTRIBUTES

Name Value
Abutment Clips IncludedYes
Anti-Rattle Spring IncludedYes
Average Current DrawCar pulls to one side during braking. Why?
Average Current Draw (Ampere)Brake squeal can be caused by improper installation of the brake pads, improperly installed brake hardware and improper brake rotor finish.
Bleeder Screw IncludedYes
Bleeder Screw Quantity1
Bleeder Screw Thread Size7/16x20
Bracket IncludedNo
Caliper ColorSilver
Caliper FinishPowder Coated
Caliper Slides IncludedYes
Caliper TypeFloating
Casting Number10
Country of OriginUnited States
Disc Brake Caliper Casting MaterialCast Iron
E-WasteNo
End 2 Fitting GenderYes
End To End Length (Inch)Powder Coated
End To End Length (Millimeter)Cast Iron
FAA_A1Not recommended. The O.E. manufacturers specified steel or phenolic pistons based on the intended use of the vehicle. It is recommended that the installer follow the manufacturer’s recommendations.
FAA_A2As a rule, always use brake fluid recommended by O.E. The fluid type is stamped on the master cylinder reservoir lid. Always use new fluid in a sealed container.
FAA_A3Inspect both calipers for binding or sticky slides or pins. Also ensure that brake hoses are not collapsed or restricted and inspect steering/suspension components for proper operation.
FAA_A4Brake squeal can be caused by improper installation of the brake pads, improperly installed brake hardware and improper brake rotor finish.
FAA_A5A symptom of a low brake pedal is usually caused by air in the system, misadjusted rear brake shoes, deteriorated brake hose(s) or a defective master cylinder.
FAA_A6A silicone grease is used on floating caliper mounting pins.
FAA_A7New hardware is included with all of our Calipers however the mounting bracket is an added option depending on part number and application. Mounting Brackets are also sold separately for most applications.
FAQ_Q1Can I switch out a Phenolic Piston Caliper for a Steel Piston Caliper or vice versa?
FAQ_Q2What type of fluid should I use: DOT 3, DOT 4, or DOT 5?
FAQ_Q3Car pulls to one side during braking. Why?
FAQ_Q4Brakes squeal all of the time. What's causing the squeal?
FAQ_Q5Could calipers be the cause of a low brake pedal?
FAQ_Q6What type of grease is used on floating caliper mounting pins?
FAQ_Q7Do all of your Calipers come with the new hardware and a mounting bracket for installation?
Flash Programming RequiredNot recommended. The O.E. manufacturers specified steel or phenolic pistons based on the intended use of the vehicle. It is recommended that the installer follow the manufacturer’s recommendations.
Fuel Filter IncludedYes
Grade TypeRegular
Hardware IncludedWhat type of grease is used on floating caliper mounting pins?
Hazardous MaterialNo
Height - Each (Inch)5.2500
Housing Height (In)Inspect both calipers for binding or sticky slides or pins. Also ensure that brake hoses are not collapsed or restricted and inspect steering/suspension components for proper operation.
Housing IncludedCan I switch out a Phenolic Piston Caliper for a Steel Piston Caliper or vice versa?
Housing Width (in)As a rule, always use brake fluid recommended by O.E. The fluid type is stamped on the master cylinder reservoir lid. Always use new fluid in a sealed container.
Inlet Fitting TypeBanjo
Inlet Port Quantity1
Inlet Port Size (Inch)0.375
Inlet Port Size (Millimeter)9.521
Inlet Thread Size3/8x24
Input Shaft Diameter (Millimeter)Yes
Item Level GTIN00884548156906
Length - Each (Inch)8.0000
Life Cycle StatusAvailable to Order
Linkage Frame or BracketA symptom of a low brake pedal is usually caused by air in the system, misadjusted rear brake shoes, deteriorated brake hose(s) or a defective master cylinder.
Material Thickness (mm)Could calipers be the cause of a low brake pedal?
Minimum Gauge Diameter (in)Yes
Motor IncludedCar pulls to one side during braking. Why?
Mounting Bolt IncludedNo
Mounting Bracket IncludedNo
Mounting Hardware IncludedYes
Mounting Hole DiameterYes
Outlet Fitting Thread Size (Millimeter)Yes
Output Shaft Diameter (in)Powder Coated
Output Shaft Diameter (mm)Cast Iron
Package ContentsCaliper; Instruction Sheet; Hardware Kit
Pad Wear Sensor IncludedNo
Pads IncludedNo
Piston Diameter (Inch)2.598
Piston Diameter (Millimeter)65.99
Piston MaterialSteel
Piston Quantity1
Plug and PlayBrake squeal can be caused by improper installation of the brake pads, improperly installed brake hardware and improper brake rotor finish.
Product ConditionRemanufactured
Pulley Attachment Type1
Quantity Per Application1
Resistance Ohms Full (PSI)1
Rust Resistant CoatingYes
Strainer Fitting Diameter (Millimeter)Can I switch out a Phenolic Piston Caliper for a Steel Piston Caliper or vice versa?
TypeNew hardware is included with all of our Calipers however the mounting bracket is an added option depending on part number and application. Mounting Brackets are also sold separately for most applications.
WarrantyNew hardware is included with all of our Calipers however the mounting bracket is an added option depending on part number and application. Mounting Brackets are also sold separately for most applications.
Weight - Each (Gross Pounds)7.2400
Width - Each (Inch)6.1300
Wire Gauge MeasurementCaliper
Wire Or Terminal QuantityYes
\No
Buy Part Now
Top