Cardone Reman 18-8040 Disc Brake Caliper
ShowMeTheParts has a wide selection of Cardone Reman products for a variety of years, makes, and models.
BUYERS GUIDE
| Make | Model | Year | Engine |
|---|---|---|---|
| MITSUBISHI FUSO | FE | 95-88 | All |
| MITSUBISHI FUSO | FE-HD | 02-96 | All |
PART INFORMATION
Brand:Cardone Reman 18-8040 Disc Brake Caliper
Part Number:18-8040
Part Type: Disc Brake Caliper
Comment:Expertly remanufactured to rigorous quality and performance standards, all CARDONE Brake Calipers are equipped with brand-new, premium components to guarantee exceptional longevity and reliability. These remanufactured brake calipers are 100% pressure-tested to deliver consistent, industry-leading brake performance. Each unit arrives with a complete set of brand-new hardware for a simple, complete installation. Caliper bracket is included when applicable.
PARTS ATTRIBUTES
| Name | Value |
|---|---|
| Bleeder Port Size | M10x1.0 |
| Brake Caliper Finish | Oil Emulsion |
| Caliper Color | Gray |
| E-Waste | No |
| FAQs | What type of grease is used on floating caliper mounting pins? |
| FAQs | What type of fluid should I use: DOT 3, DOT 4, or DOT 5? |
| FAQs | Not recommended. The O.E. manufacturers specified steel or phenolic pistons based on the intended use of the vehicle. It is recommended that the installer follow the manufacturer’s recommendations. |
| FAQs | New hardware is included with all of our Calipers however the mounting bracket is an added option depending on part number and application. Mounting Brackets are also sold separately for most applications. |
| FAQs | Inspect both calipers for binding or sticky slides or pins. Also ensure that brake hoses are not collapsed or restricted and inspect steering/suspension components for proper operation. |
| FAQs | Do all of your Calipers come with the new hardware and a mounting bracket for installation? |
| FAQs | Could calipers be the cause of a low brake pedal? |
| FAQs | Car pulls to one side during braking. Why? |
| FAQs | Can I switch out a Phenolic Piston Caliper for a Steel Piston Caliper or vice versa? |
| FAQs | Brakes squeal all of the time. What's causing the squeal? |
| FAQs | Brake squeal can be caused by improper installation of the brake pads, improperly installed brake hardware and improper brake rotor finish. |
| FAQs | As a rule, always use brake fluid recommended by O.E. The fluid type is stamped on the master cylinder reservoir lid. Always use new fluid in a sealed container. |
| FAQs | A symptom of a low brake pedal is usually caused by air in the system, misadjusted rear brake shoes, deteriorated brake hose(s) or a defective master cylinder. |
| FAQs | A silicone grease is used on floating caliper mounting pins. |
| Features and Benefits | Calipers are treated with a special formulated rust inhibitor and kept in the original equipment finish. |
| Features and Benefits | As a remanufactured Original Equipment part, this unit guarantees a perfect vehicle fit. |
| Features and Benefits | A plastic cap plug protects every brake port thread to ensure trouble-free installation. |
| Features and Benefits | Rubber seals are replaced with new high temperature EPDM rubber for extended life and optimum performance. |
| Features and Benefits | Pistons are durable, resistant to cracking or pitting and handle great loads. |
| Features and Benefits | Our remanufacturing process is earth-friendly, as it reduces the energy and raw material needed to make a new part by 80%. |
| Features and Benefits | New washers are included where applicable for a proper seal. |
| Features and Benefits | New stainless steel hardware clips and new mounting pins are included where applicable. |
| Features and Benefits | New bleeder screws provide trouble-free bleeding and a positive seal. |
| Features and Benefits | New banjo bolts are included where applicable to ensure a perfect fit and quick installation. |
| Features and Benefits | Mounting bracket is included where applicable for a hassle-free installation. |
| Hazardous Material | No |
| Height - Each (Inch) | 5.25 |
| Inlet Port Size | M10x1.0 |
| Installation Hardware Included | Yes |
| Item Level GTIN | 00082617451369 |
| Length - Each (Inch) | 7.875 |
| Life Cycle Status | Available to Order |
| Life Cycle Status Description | Available to Order - Part is released to customers for ordering. |
| Mounting Bolts Included | No |
| Package Contents | Caliper; Hardware Kit |
| Pads Included | No |
| Piston Material | Steel |
| Piston Quantity | 1 |
| Piston Size (OD) (in) | 2.01 |
| Piston Size (OD) (mm) | 51.054 |
| Product Condition | Remanufactured |
| Quantity Per Application | 1 |
| Weight - Each (Gross Pounds) | 8.5 |
| Width - Each (Inch) | 6.125 |
