Cardone Reman 18-5117 Disc Brake Caliper For CADILLAC

Buy Part Now

ShowMeTheParts has a wide selection of Cardone Reman products for a variety of years, makes, and models.

Cardone Reman 18-5117 Disc Brake Caliper For CADILLAC

BUYERS GUIDE

Make Model Year Engine
CADILLACCTS2008-14All
CADILLACCTS2008-14All

PART INFORMATION

Brand:Disc Brake Caliper by Cardone Reman For CADILLAC | ShowMeTheParts.com
Part Number:185117
Part Type: Disc Brake Caliper
Comment:Expertly remanufactured to rigorous quality and performance standards, all CARDONE Brake Calipers are equipped with brand-new, premium components to guarantee exceptional longevity and reliability. These remanufactured brake calipers are 100% pressure-tested to deliver consistent, industry-leading brake performance. Each unit arrives with a complete set of brand-new hardware for a simple, complete installation. Caliper bracket is included when applicable.

PARTS ATTRIBUTES

Name Value
Bleeder Port SizeM7x1.0
Brake Caliper FinishOil Emulsion
Caliper ColorGray
E-WasteNo
FAQsA silicone grease is used on floating caliper mounting pins.
FAQsA symptom of a low brake pedal is usually caused by air in the system, misadjusted rear brake shoes, deteriorated brake hose(s) or a defective master cylinder.
FAQsAs a rule, always use brake fluid recommended by O.E. The fluid type is stamped on the master cylinder reservoir lid. Always use new fluid in a sealed container.
FAQsBrake squeal can be caused by improper installation of the brake pads, improperly installed brake hardware and improper brake rotor finish.
FAQsBrakes squeal all of the time. What's causing the squeal?
FAQsCan I switch out a Phenolic Piston Caliper for a Steel Piston Caliper or vice versa?
FAQsCar pulls to one side during braking. Why?
FAQsCould calipers be the cause of a low brake pedal?
FAQsDo all of your Calipers come with the new hardware and a mounting bracket for installation?
FAQsInspect both calipers for binding or sticky slides or pins. Also ensure that brake hoses are not collapsed or restricted and inspect steering/suspension components for proper operation.
FAQsNew hardware is included with all of our Calipers however the mounting bracket is an added option depending on part number and application. Mounting Brackets are also sold separately for most applications.
FAQsNot recommended. The O.E. manufacturers specified steel or phenolic pistons based on the intended use of the vehicle. It is recommended that the installer follow the manufacturer’s recommendations.
FAQsWhat type of fluid should I use: DOT 3, DOT 4, or DOT 5?
FAQsWhat type of grease is used on floating caliper mounting pins?
Features and BenefitsA plastic cap plug protects every brake port thread to ensure trouble-free installation.
Features and BenefitsAs a remanufactured Original Equipment part, this unit guarantees a perfect vehicle fit.
Features and BenefitsCalipers are treated with a special formulated rust inhibitor and kept in the original equipment finish.
Features and BenefitsMounting bracket is included where applicable for a hassle-free installation.
Features and BenefitsNew banjo bolts are included where applicable to ensure a perfect fit and quick installation.
Features and BenefitsNew bleeder screws provide trouble-free bleeding and a positive seal.
Features and BenefitsNew stainless steel hardware clips and new mounting pins are included where applicable.
Features and BenefitsNew washers are included where applicable for a proper seal.
Features and BenefitsOur remanufacturing process is earth-friendly, as it reduces the energy and raw material needed to make a new part by 80%.
Features and BenefitsPistons are durable, resistant to cracking or pitting and handle great loads.
Features and BenefitsRubber seals are replaced with new high temperature EPDM rubber for extended life and optimum performance.
Hazardous MaterialNo
Height - Each (Inch)5.25
Inlet Port SizeM10x1.0
Installation Hardware IncludedYes
Item Level GTIN00082617875073
Length - Each (Inch)9.563
Life Cycle StatusAvailable to Order
Life Cycle Status DescriptionAvailable to Order - Part is released to customers for ordering.
Mounting Bolts IncludedNo
Mounting TypeM10x1.0
Package ContentsCaliper; Hardware Kit
Pads IncludedNo
Piston MaterialSteel
Piston Quantity2
Piston Size (OD) (in)1.655
Piston Size (OD) (mm)42.037
Product ConditionRemanufactured
Quantity Per Application1
Weight - Each (Gross Pounds)8
Width - Each (Inch)7.25
Wire Gauge MeasurementCaliper
Buy Part Now
Top