Cardone Reman 18-4167 Disc Brake Caliper

Buy Part Now

ShowMeTheParts has a wide selection of Cardone Reman products for a variety of years, makes, and models.

Cardone Reman 18-4167 Disc Brake Caliper

BUYERS GUIDE

MakeModelYearEngine
CHEVROLETC3086-79All
CHEVROLETC3500-91All
CHEVROLETC350000-91All
CHEVROLETC3500HD02-91All
CHEVROLETC5090-88All
CHEVROLETC5500 KODIAK91-90All
CHEVROLETC6090-88All
CHEVROLETC60 KODIAK1990All
CHEVROLETC7090-88All
CHEVROLETC70 KODIAK1990All
CHEVROLETG3096-79All
CHEVROLETK3086-79All
CHEVROLETP3099-79All
CHEVROLETP4090-83All
CHEVROLETP6090-83All
CHEVROLETR3088-87All
CHEVROLETR350091-89All
CHEVROLETV3088-87All
CHEVROLETV350091-89All
DODGEW25093-90All
DODGEW35093-90All
FREIGHTLINERMT3505-97All
FREIGHTLINERMT4505-98All
FREIGHTLINERMT5505-99All
GMCC350000-91All
GMCC350086-79All
GMCC3500HD02-91All
GMCC500090-88All
GMCC5000 TOPKICK1990All
GMCC600090-88All
GMCC6000 TOPKICK1990All
GMCC700090-88All
GMCC7000 TOPKICK1990All
GMCG350096-79All
GMCK350086-79All
GMCP350099-79All
GMCP450090-83All
GMCR350091-87All
GMCV350091-87All

PART INFORMATION

Brand:Cardone Reman 18-4167 Disc Brake Caliper
Part Number:18-4167
Part Type: Disc Brake Caliper
Comment:Expertly remanufactured to rigorous quality and performance standards, all CARDONE® Brake Calipers are equipped with brand-new, premium components to guarantee exceptional longevity and reliability. These remanufactured brake calipers are 100% pressure-tested to deliver consistent, industry-leading brake performance. Each unit arrives with a complete set of brand-new hardware for a simple, complete installation. Caliper bracket is included when applicable.

PARTS ATTRIBUTES

NameValue
Bleeder Port SizeM10x1.5
Brake Caliper FinishOil Emulsion
Caliper ColorGray
E-WasteNo
FAQsA silicone grease is used on floating caliper mounting pins.
FAQsWhat type of grease is used on floating caliper mounting pins?
FAQsWhat type of fluid should I use: DOT 3, DOT 4, or DOT 5?
FAQsNot recommended. The O.E. manufacturers specified steel or phenolic pistons based on the intended use of the vehicle. It is recommended that the installer follow the manufacturer’s recommendations.
FAQsNew hardware is included with all of our Calipers however the mounting bracket is an added option depending on part number and application. Mounting Brackets are also sold separately for most applications.
FAQsInspect both calipers for binding or sticky slides or pins. Also ensure that brake hoses are not collapsed or restricted and inspect steering/suspension components for proper operation.
FAQsDo all of your Calipers come with the new hardware and a mounting bracket for installation?
FAQsCould calipers be the cause of a low brake pedal?
FAQsCar pulls to one side during braking. Why?
FAQsCan I switch out a Phenolic Piston Caliper for a Steel Piston Caliper or vice versa?
FAQsBrakes squeal all of the time. What's causing the squeal?
FAQsBrake squeal can be caused by improper installation of the brake pads, improperly installed brake hardware and improper brake rotor finish.
FAQsAs a rule, always use brake fluid recommended by O.E. The fluid type is stamped on the master cylinder reservoir lid. Always use new fluid in a sealed container.
FAQsA symptom of a low brake pedal is usually caused by air in the system, misadjusted rear brake shoes, deteriorated brake hose(s) or a defective master cylinder.
Features and BenefitsRubber seals are replaced with new high temperature EPDM rubber for extended life and optimum performance.
Features and BenefitsPistons are durable, resistant to cracking or pitting and handle great loads.
Features and BenefitsOur remanufacturing process is earth-friendly, as it reduces the energy and raw material needed to make a new part by 80%.
Features and BenefitsNew washers are included where applicable for a proper seal.
Features and BenefitsNew stainless steel hardware clips and new mounting pins are included where applicable.
Features and BenefitsNew bleeder screws provide trouble-free bleeding and a positive seal.
Features and BenefitsNew banjo bolts are included where applicable to ensure a perfect fit and quick installation.
Features and BenefitsMounting bracket is included where applicable for a hassle-free installation.
Features and BenefitsCalipers are treated with a special formulated rust inhibitor and kept in the original equipment finish.
Features and BenefitsAs a remanufactured Original Equipment part, this unit guarantees a perfect vehicle fit.
Features and BenefitsA plastic cap plug protects every brake port thread to ensure trouble-free installation.
Hazardous MaterialNo
Height - Each (Inch)5.25
Inlet Port SizeM10x1.5
Installation Hardware IncludedYes
Item Level GTIN00082617011938
Length - Each (Inch)9.563
Life Cycle StatusAvailable to Order
Life Cycle Status DescriptionAvailable to Order - Part is released to customers for ordering.
Mounting Bolts IncludedNo
Package ContentsCaliper; Hardware Kit
Pads IncludedNo
Piston MaterialSteel
Piston Quantity1
Piston Size (OD) (in)3.368
Piston Size (OD) (mm)85.5472
Product ConditionRemanufactured
Quantity Per Application1
Weight - Each (Gross Pounds)16.37
Width - Each (Inch)7.25
Buy Part Now
Top