Cardone Reman 18-4072 Disc Brake Caliper For AVANTI,BUICK,CHEVROLET,GMC,ISUZU,OLDSMOBILE,PONTIAC

Buy Part Now

ShowMeTheParts has a wide selection of Cardone Reman products for a variety of years, makes, and models.

Cardone Reman 18-4072 Disc Brake Caliper For AVANTI,BUICK,CHEVROLET,GMC,ISUZU,OLDSMOBILE,PONTIAC

BUYERS GUIDE

Make Model Year Engine
AVANTIII1968-85All
BUICKCENTURY1978-81All
BUICKREGAL1978-87All
CHEVROLETBLAZER1995-97All
CHEVROLETCAMARO1982-92All
CHEVROLETEL CAMINO1978-87All
CHEVROLETLLV1987-95All
CHEVROLETMALIBU1978-83All
CHEVROLETMONTE CARLO1978-88All
CHEVROLETS101982-2003All
CHEVROLETS10 BLAZER1983-94All
GMCCABALLERO1978-87All
GMCJIMMY1992-97All
GMCS151982-90All
GMCS15 JIMMY1983-91All
GMCSONOMA1991-2003All
ISUZUHOMBRE1996-2000All
OLDSMOBILECUTLASS1978-81All
OLDSMOBILECUTLASS1985-87All
OLDSMOBILECUTLASS CALAIS1978-84All
OLDSMOBILECUTLASS CRUISER1980-83All
OLDSMOBILECUTLASS SALON1978-80All
OLDSMOBILECUTLASS SALON1985-87All
OLDSMOBILECUTLASS SUPREME1978-88All
PONTIACBONNEVILLE1982-86All
PONTIACFIREBIRD1982-92All
PONTIACGRAND AM1978-80All
PONTIACGRAND LEMANS1978-83All
PONTIACGRAND PRIX1978-87All
PONTIACLEMANS1978-81All

PART INFORMATION

Brand:Disc Brake Caliper by Cardone Reman For AVANTI,BUICK,CHEVROLET,GMC,ISUZU,OLDSMOBILE,PONTIAC | ShowMeTheParts.com
Part Number:184072
Part Type: Disc Brake Caliper
Comment:Expertly remanufactured to rigorous quality and performance standards, all CARDONE Brake Calipers are equipped with brand-new, premium components to guarantee exceptional longevity and reliability. These remanufactured brake calipers are 100% pressure-tested to deliver consistent, industry-leading brake performance. Each unit arrives with a complete set of brand-new hardware for a simple, complete installation. Caliper bracket is included when applicable.

PARTS ATTRIBUTES

Name Value
Abutment Clips IncludedNo
Anti-Rattle Spring IncludedYes
Average Current DrawCar pulls to one side during braking. Why?
Average Current Draw (Ampere)Brake squeal can be caused by improper installation of the brake pads, improperly installed brake hardware and improper brake rotor finish.
Bleeder Screw Cap IncludedNo
Bleeder Screw IncludedYes
Bleeder Screw Quantity1
Bleeder Thread SizeM10x1.5
Bracket IncludedNo
Caliper ColorGray
Caliper FinishOil Emulsion
Caliper Slides IncludedYes
Caliper TypeFloating
Casting Number366
Contains Electronic ComponentsNo
Country of OriginUnited States
Disc Brake Caliper Casting MaterialCast Iron
Does it require SDSNo
Dust Boots IncludedYes
E-WasteNo
End 2 Fitting GenderYes
End To End Length (Inch)Oil Emulsion
End To End Length (Millimeter)Cast Iron
FAA_A1Not recommended. The O.E. manufacturers specified steel or phenolic pistons based on the intended use of the vehicle. It is recommended that the installer follow the manufacturer’s recommendations.
FAA_A2As a rule, always use brake fluid recommended by O.E. The fluid type is stamped on the master cylinder reservoir lid. Always use new fluid in a sealed container.
FAA_A3Inspect both calipers for binding or sticky slides or pins. Also ensure that brake hoses are not collapsed or restricted and inspect steering/suspension components for proper operation.
FAA_A4Brake squeal can be caused by improper installation of the brake pads, improperly installed brake hardware and improper brake rotor finish.
FAA_A5A symptom of a low brake pedal is usually caused by air in the system, misadjusted rear brake shoes, deteriorated brake hose(s) or a defective master cylinder.
FAA_A6A silicone grease is used on floating caliper mounting pins.
FAA_A7New hardware is included with all of our Calipers however the mounting bracket is an added option depending on part number and application. Mounting Brackets are also sold separately for most applications.
FAQ_Q1Can I switch out a Phenolic Piston Caliper for a Steel Piston Caliper or vice versa?
FAQ_Q2What type of fluid should I use: DOT 3, DOT 4, or DOT 5?
FAQ_Q3Car pulls to one side during braking. Why?
FAQ_Q4Brakes squeal all of the time. What's causing the squeal?
FAQ_Q5Could calipers be the cause of a low brake pedal?
FAQ_Q6What type of grease is used on floating caliper mounting pins?
FAQ_Q7Do all of your Calipers come with the new hardware and a mounting bracket for installation?
Flash Programming RequiredNot recommended. The O.E. manufacturers specified steel or phenolic pistons based on the intended use of the vehicle. It is recommended that the installer follow the manufacturer’s recommendations.
Fuel Filter IncludedYes
Grade TypeRegular
Hardware IncludedWhat type of grease is used on floating caliper mounting pins?
Hazardous MaterialNo
Height - Each (Inch)5.2500
Housing Height (In)Inspect both calipers for binding or sticky slides or pins. Also ensure that brake hoses are not collapsed or restricted and inspect steering/suspension components for proper operation.
Housing IncludedCan I switch out a Phenolic Piston Caliper for a Steel Piston Caliper or vice versa?
Housing Width (in)As a rule, always use brake fluid recommended by O.E. The fluid type is stamped on the master cylinder reservoir lid. Always use new fluid in a sealed container.
Inlet Fitting TypeBanjo
Inlet Port Quantity1
Inlet Port Size (Inch)0.394
Inlet Port Size (Millimeter)10.00366
Inlet Thread SizeM10x1.5
Input Shaft Diameter (Inch)No
Input Shaft Diameter (Millimeter)Yes
Input Shaft Spline QuantityYes
Is Item A ChemicalNo
Is Or Contains A BatteryNo
Is Or Contains A BulbNo
Is Prop Sixty Five AffectedNo
Is the item CARB affectedNo
Item Level GTIN00082617011112
Length (in)M10x1.5
Length - Each (Inch)8.0000
Life Cycle StatusAvailable to Order
Linkage Frame or BracketA symptom of a low brake pedal is usually caused by air in the system, misadjusted rear brake shoes, deteriorated brake hose(s) or a defective master cylinder.
Material Thickness (mm)Could calipers be the cause of a low brake pedal?
Maximum Gauge Diameter (in)Yes
Minimum Gauge Diameter (in)Yes
Motor IncludedCar pulls to one side during braking. Why?
Mounting Bolt IncludedYes
Mounting Bracket IncludedNo
Mounting Hardware IncludedYes
Mounting Hole DiameterYes
Mounting Hole Diameter (Inch)0.618
Mounting Hole Diameter (Millimeter)15.69102
Mounting Hole Thread Diameter (Inch)0.618
Mounting Hole Thread Diameter (Millimeter)15.69102
Outlet Fitting Thread Size (Millimeter)Yes
Output Shaft Diameter (Inch)M10x1.5
Output Shaft Diameter (in)Oil Emulsion
Output Shaft Diameter (mm)Cast Iron
Package ContentsCaliper; Instruction Sheet; Hardware Kit
Pad Wear Sensor IncludedNo
Pads IncludedNo
Piston Diameter (Inch)2.496
Piston Diameter (Millimeter)63.3984
Piston MaterialSteel
Piston Quantity1
Plug and PlayBrake squeal can be caused by improper installation of the brake pads, improperly installed brake hardware and improper brake rotor finish.
Product ConditionRemanufactured
Pulley Attachment Type1
Quantity Per Application1
Resistance Ohms Full (PSI)1
Rust Resistant CoatingYes
Strainer Fitting Diameter (Millimeter)Can I switch out a Phenolic Piston Caliper for a Steel Piston Caliper or vice versa?
TypeNew hardware is included with all of our Calipers however the mounting bracket is an added option depending on part number and application. Mounting Brackets are also sold separately for most applications.
WarrantyNew hardware is included with all of our Calipers however the mounting bracket is an added option depending on part number and application. Mounting Brackets are also sold separately for most applications.
Weight - Each (Gross Pounds)7.2500
Width (in)No
Width - Each (Inch)6.1250
Wire Gauge MeasurementCaliper
Wire Or Terminal QuantityYes
Buy Part Now
Top