Cardone Reman 11-4497 Brake Master Cylinder

Buy Part Now

ShowMeTheParts has a wide selection of Cardone Reman products for a variety of years, makes, and models.

Cardone Reman 11-4497 Brake Master Cylinder

BUYERS GUIDE

MakeModelYearEngine
BMW528I16-11All
BMW528I XDRIVE16-12All
BMW535D16-14All
BMW535D XDRIVE16-14All
BMW535I16-11All
BMW535I GT16-11All
BMW535I GT XDRIVE16-11All
BMW535I XDRIVE16-11All
BMW550I16-11All
BMW550I XDRIVE16-11All
BMW640I18-12All
BMW640I GRAN COUPE19-13All
BMW640I XDRIVE18-14All
BMW640I XDRIVE GRAN COUPE19-14All
BMW650I18-12All
BMW650I GRAN COUPE18-13All
BMW650I XDRIVE18-12All
BMW650I XDRIVE GRAN COUPE18-13All
BMWACTIVEHYBRID 52012All
BMWALPINA B6 GRAN COUPE2016All
BMWALPINA B6 XDRIVE GRAN COUPE18-15All

PART INFORMATION

Brand:Cardone Reman 11-4497 Brake Master Cylinder
Part Number:11-4497
Part Type: Brake Master Cylinder
Comment:CARDONE Remanufactured Master Cylinders are re-engineered, built and tested to match O.E. performance. Each unit features new, O.E.-quality seals and cups to ensure leak-free, long-lasting performance. Cast-iron master cylinders are treated with a premium protective coating to minimize rust and extend product life. All units are 100% computer tested to ensure perfect fit and function.

PARTS ATTRIBUTES

NameValue
Bore Diameter (N)0.875
E-WasteNo
FAQsWhy is the piston stuck inside the bore of my master cylinder?
FAQsWhat’s the difference between Dot 3, 4 and 5?
FAQsWhat type of fluid should I use: DOT 3, DOT 4 or DOT 5?
FAQsWhat causes the car to pull to one side during braking?
FAQsWhat causes the brakes to lock up after only a couple of miles?
FAQsThis is caused by a problem with the caliper or a brake hose.
FAQsThe master cylinder is working correctly. Check for a faulty brake booster or frozen wheel cylinder/caliper.
FAQsThe brake pedal is low and spongy. Is it a bad master cylinder?
FAQsSimply plug the master cylinder ports and press the brake pedal. If the master cylinder is bypassing, the pedal will go down. If the pedal stops hard, the master cylinder is OK.
FAQsOne side of my front brakes won’t release, why?
FAQsMy original master cylinder leaked out of the back of the piston into the booster area. Why?
FAQsI replaced the master cylinder and now the pedal is high and hard. Why?
FAQsHow can I test a master cylinder to see if it's bypassing?
FAQsDot 3 and 4 are Glycol-based fluids and Dot 5 is a silicone-based fluid.
FAQsDoes a step bore style master cylinder require a specific bleeding process?
FAQsCheck the steering and suspension. Inspect both calipers for binding or sticky slides or pins. Check brake lining for oil/grease or uneven wear. Inspect brake hoses for restriction. Check for proper tire pressure.
FAQsCheck booster for a defective push rod seal. If this seal is bad, it could drain the brake fluid out of the master cylinder.
FAQsAs a rule, always use the brake fluid recommended by the O.E. which is stamped on the master cylinder lid. Note: Always use new fluid from a sealed container.
Features and BenefitsOur remanufacturing process is earth-friendly, as it reduces the energy and raw material needed to make a new part by 80%.
Features and BenefitsOnly new O.E.-quality seals and cups are used in the remanufacturing process to ensure O.E. performance and reliability. All rubber components meet S.A.E. specifications.
Features and BenefitsCast-iron master cylinders feature a premium protective coating to minimize rust and extend unit life.
Features and BenefitsBores meet critical micro-finish specifications to eliminate pitting and corrosion, a cause of premature failure.
Features and BenefitsBleeding kits are supplied with the unit to make the bleeding process faster and easier (where applicable).
Features and BenefitsAs a remanufactured Original Equipment part, this unit guarantees a perfect vehicle fit.
Features and BenefitsPlastic reservoirs are vacuum-tested to ensure they are leak free.
Features and BenefitsPiston assemblies are height-gauged to ensure the master cylinder equals the O.E. unit performance.
Hazardous MaterialNo
Height - Each (Inch)11.125
Installation Hardware IncludedNo
Item Level GTIN00884548020603
Length - Each (Inch)3.625
Life Cycle StatusAvailable to Order
Life Cycle Status DescriptionAvailable to Order - Part is released to customers for ordering.
Master Cylinder Color/FinishGray
Master Cylinder MaterialAluminum
Mounting Hole Quantity2
Package ContentsMaster Cylinder
Port Quantity2
Primary Port SizeM12 x 1.0
Product ConditionRemanufactured
Quantity Per Application1
Reservoir IncludedNo
Secondary Port SizeM12 x 1.0
Weight - Each (Gross Pounds)2
Width - Each (Inch)3.625
Buy Part Now
Top