Cardone Reman 10-8036 Brake Master Cylinder

Buy Part Now

ShowMeTheParts has a wide selection of Cardone Reman products for a variety of years, makes, and models.

Cardone Reman 10-8036 Brake Master Cylinder


GMCC5000 TOPKICK91-90All
GMCC6000 TOPKICK96-91All
GMCC7000 TOPKICK96-91All


Brand:Cardone Reman 10-8036 Brake Master Cylinder
Part Number:10-8036
Part Type: Brake Master Cylinder
Comment:CARDONE Remanufactured Master Cylinders are re-engineered, built and tested to match O.E. performance. Each unit features new, O.E.-quality seals and cups to ensure leak-free, long-lasting performance. Cast-iron master cylinders are treated with a premium protective coating to minimize rust and extend product life. All units are 100% computer tested to ensure perfect fit and function.


Bore Diameter (N)1.75
FAQsAs a rule, always use the brake fluid recommended by the O.E. which is stamped on the master cylinder lid. Note: Always use new fluid from a sealed container.
FAQsWhy is the piston stuck inside the bore of my master cylinder?
FAQsWhat’s the difference between Dot 3, 4 and 5?
FAQsWhat type of fluid should I use: DOT 3, DOT 4 or DOT 5?
FAQsWhat causes the car to pull to one side during braking?
FAQsWhat causes the brakes to lock up after only a couple of miles?
FAQsThis is caused by a problem with the caliper or a brake hose.
FAQsThe master cylinder is working correctly. Check for a faulty brake booster or frozen wheel cylinder/caliper.
FAQsThe brake pedal is low and spongy. Is it a bad master cylinder?
FAQsSimply plug the master cylinder ports and press the brake pedal. If the master cylinder is bypassing, the pedal will go down. If the pedal stops hard, the master cylinder is OK.
FAQsOne side of my front brakes won’t release, why?
FAQsMy original master cylinder leaked out of the back of the piston into the booster area. Why?
FAQsI replaced the master cylinder and now the pedal is high and hard. Why?
FAQsHow can I test a master cylinder to see if it's bypassing?
FAQsDot 3 and 4 are Glycol-based fluids and Dot 5 is a silicone-based fluid.
FAQsDoes a step bore style master cylinder require a specific bleeding process?
FAQsCheck the steering and suspension. Inspect both calipers for binding or sticky slides or pins. Check brake lining for oil/grease or uneven wear. Inspect brake hoses for restriction. Check for proper tire pressure.
FAQsCheck booster for a defective push rod seal. If this seal is bad, it could drain the brake fluid out of the master cylinder.
Features and BenefitsCast-iron master cylinders feature a premium protective coating to minimize rust and extend unit life.
Features and BenefitsBores meet critical micro-finish specifications to eliminate pitting and corrosion, a cause of premature failure.
Features and BenefitsBleeding kits are supplied with the unit to make the bleeding process faster and easier (where applicable).
Features and BenefitsAs a remanufactured Original Equipment part, this unit guarantees a perfect vehicle fit.
Features and BenefitsPlastic reservoirs are vacuum-tested to ensure they are leak free.
Features and BenefitsPiston assemblies are height-gauged to ensure the master cylinder equals the O.E. unit performance.
Features and BenefitsOur remanufacturing process is earth-friendly, as it reduces the energy and raw material needed to make a new part by 80%.
Features and BenefitsOnly new O.E.-quality seals and cups are used in the remanufacturing process to ensure O.E. performance and reliability. All rubber components meet S.A.E. specifications.
Hazardous MaterialNo
Height - Each (Inch)7.125
Installation Hardware IncludedNo
Item Level GTIN00082617514408
Length - Each (Inch)11.875
Life Cycle StatusAvailable to Order
Life Cycle Status DescriptionAvailable to Order - Part is released to customers for ordering.
Master Cylinder Color/FinishGray
Master Cylinder MaterialCast Iron
Mounting Hole Quantity4
Package ContentsMaster Cylinder
Port Quantity2
Primary Port Size9/16 x 18
Product ConditionRemanufactured
Quantity Per Application1
Reservoir IncludedYes
Reservoir MaterialPlastic
Reservoir TypeAssembled
Secondary Port Size1/2 x 20
Weight - Each (Gross Pounds)12.44
Width - Each (Inch)7.625
Buy Part Now