Cardone Reman 10-1870 Brake Master Cylinder

Buy Part Now

ShowMeTheParts has a wide selection of Cardone Reman products for a variety of years, makes, and models.

Cardone Reman 10-1870 Brake Master Cylinder

BUYERS GUIDE

MakeModelYearEngine
BUICKELECTRA89-81All
BUICKESTATE WAGON83-81All
BUICKLESABRE90-81All
CADILLACBROUGHAM92-87All
CADILLACCOMMERCIAL CHASSIS1992All
CADILLACCOMMERCIAL CHASSIS84-81All
CADILLACDEVILLE84-81All
CADILLACFLEETWOOD86-81All
CHECKERMARATHON82-81All
CHEVROLETBEL AIR1981All
CHEVROLETCAMARO1981All
CHEVROLETCAPRICE90-81All
CHEVROLETIMPALA85-81All
OLDSMOBILE9884-81All
OLDSMOBILECUSTOM CRUISER90-81All
OLDSMOBILEDELTA 8885-81All
PONTIACBONNEVILLE1981All
PONTIACCATALINA1981All
PONTIACFIREBIRD1981All
PONTIACLAURENTIAN1981All
PONTIACPARISIENNE86-81All
PONTIACSAFARI89-87All

PART INFORMATION

Brand:Cardone Reman 10-1870 Brake Master Cylinder
Part Number:10-1870
Part Type: Brake Master Cylinder
Comment:CARDONE Remanufactured Master Cylinders are re-engineered, built and tested to match O.E. performance. Each unit features new, O.E.-quality seals and cups to ensure leak-free, long-lasting performance. Cast-iron master cylinders are treated with a premium protective coating to minimize rust and extend product life. All units are 100% computer tested to ensure perfect fit and function.

PARTS ATTRIBUTES

NameValue
Bore Diameter (N)1.125
E-WasteNo
FAQsI replaced the master cylinder and now the pedal is high and hard. Why?
FAQsHow can I test a master cylinder to see if it's bypassing?
FAQsOne side of my front brakes won’t release, why?
FAQsCheck the steering and suspension. Inspect both calipers for binding or sticky slides or pins. Check brake lining for oil/grease or uneven wear. Inspect brake hoses for restriction. Check for proper tire pressure.
FAQsAs a rule, always use the brake fluid recommended by the O.E. which is stamped on the master cylinder lid. Note: Always use new fluid from a sealed container.
FAQsWhy is the piston stuck inside the bore of my master cylinder?
FAQsThe brake pedal is low and spongy. Is it a bad master cylinder?
FAQsSimply plug the master cylinder ports and press the brake pedal. If the master cylinder is bypassing, the pedal will go down. If the pedal stops hard, the master cylinder is OK.
FAQsWhat causes the car to pull to one side during braking?
FAQsDoes a step bore style master cylinder require a specific bleeding process?
FAQsCheck booster for a defective push rod seal. If this seal is bad, it could drain the brake fluid out of the master cylinder.
FAQsWhat type of fluid should I use: DOT 3, DOT 4 or DOT 5?
FAQsThis is caused by a problem with the caliper or a brake hose.
FAQsMy original master cylinder leaked out of the back of the piston into the booster area. Why?
FAQsThe master cylinder is working correctly. Check for a faulty brake booster or frozen wheel cylinder/caliper.
FAQsWhat causes the brakes to lock up after only a couple of miles?
FAQsWhat’s the difference between Dot 3, 4 and 5?
FAQsDot 3 and 4 are Glycol-based fluids and Dot 5 is a silicone-based fluid.
Features and BenefitsBleeding kits are supplied with the unit to make the bleeding process faster and easier (where applicable).
Features and BenefitsOnly new O.E.-quality seals and cups are used in the remanufacturing process to ensure O.E. performance and reliability. All rubber components meet S.A.E. specifications.
Features and BenefitsAs a remanufactured Original Equipment part, this unit guarantees a perfect vehicle fit.
Features and BenefitsBores meet critical micro-finish specifications to eliminate pitting and corrosion, a cause of premature failure.
Features and BenefitsOur remanufacturing process is earth-friendly, as it reduces the energy and raw material needed to make a new part by 80%.
Features and BenefitsCast-iron master cylinders feature a premium protective coating to minimize rust and extend unit life.
Features and BenefitsPiston assemblies are height-gauged to ensure the master cylinder equals the O.E. unit performance.
Features and BenefitsPlastic reservoirs are vacuum-tested to ensure they are leak free.
Hazardous MaterialNo
Height - Each (Inch)9.5
Installation Hardware IncludedNo
Item Level GTIN00082617006439
Length - Each (Inch)6.625
Life Cycle StatusAvailable to Order
Life Cycle Status DescriptionAvailable to Order - Part is released to customers for ordering.
Master Cylinder Color/FinishGray
Master Cylinder MaterialAluminum
Mounting Hole Quantity2
Package ContentsMaster Cylinder
Port Quantity2
Primary Port Size1/2 x 20
Product ConditionRemanufactured
Quantity Per Application1
Reservoir IncludedYes
Reservoir MaterialPlastic
Reservoir TypeAssembled
Secondary Port Size9/16 x 18
Weight - Each (Gross Pounds)2.96
Width - Each (Inch)5.375
Buy Part Now
Top