Cardone Reman 10-1394 Brake Master Cylinder

Buy Part Now

ShowMeTheParts has a wide selection of Cardone Reman products for a variety of years, makes, and models.

Cardone Reman 10-1394 Brake Master Cylinder

BUYERS GUIDE

MakeModelYearEngine
FORDCOUNTRY SEDAN1967All
FORDCOUNTRY SQUIRE1967All
FORDCUSTOM1967All
FORDCUSTOM 5001967All
FORDGALAXIE1967All
FORDGALAXIE 5001967All
FORDLTD1967All
FORDRANCH WAGON1967All
LINCOLNCONTINENTAL71-67All
MERCURYBROUGHAM1967All
MERCURYCOLONY PARK1967All
MERCURYCOMMUTER1967All
MERCURYMARAUDER1967All
MERCURYMARQUIS1967All
MERCURYMONTCLAIR1967All
MERCURYMONTEREY1967All
MERCURYPARK LANE1967All

PART INFORMATION

Brand:Cardone Reman 10-1394 Brake Master Cylinder
Part Number:10-1394
Part Type: Brake Master Cylinder
Comment:CARDONE Remanufactured Master Cylinders are re-engineered, built and tested to match O.E. performance. Each unit features new, O.E.-quality seals and cups to ensure leak-free, long-lasting performance. Cast-iron master cylinders are treated with a premium protective coating to minimize rust and extend product life. All units are 100% computer tested to ensure perfect fit and function.

PARTS ATTRIBUTES

NameValue
Bore Diameter (N)1.00
E-WasteNo
FAQsMy original master cylinder leaked out of the back of the piston into the booster area. Why?
FAQsWhat causes the brakes to lock up after only a couple of miles?
FAQsDot 3 and 4 are Glycol-based fluids and Dot 5 is a silicone-based fluid.
FAQsWhy is the piston stuck inside the bore of my master cylinder?
FAQsWhat type of fluid should I use: DOT 3, DOT 4 or DOT 5?
FAQsAs a rule, always use the brake fluid recommended by the O.E. which is stamped on the master cylinder lid. Note: Always use new fluid from a sealed container.
FAQsWhat’s the difference between Dot 3, 4 and 5?
FAQsCheck booster for a defective push rod seal. If this seal is bad, it could drain the brake fluid out of the master cylinder.
FAQsCheck the steering and suspension. Inspect both calipers for binding or sticky slides or pins. Check brake lining for oil/grease or uneven wear. Inspect brake hoses for restriction. Check for proper tire pressure.
FAQsDoes a step bore style master cylinder require a specific bleeding process?
FAQsThe master cylinder is working correctly. Check for a faulty brake booster or frozen wheel cylinder/caliper.
FAQsThis is caused by a problem with the caliper or a brake hose.
FAQsSimply plug the master cylinder ports and press the brake pedal. If the master cylinder is bypassing, the pedal will go down. If the pedal stops hard, the master cylinder is OK.
FAQsThe brake pedal is low and spongy. Is it a bad master cylinder?
FAQsI replaced the master cylinder and now the pedal is high and hard. Why?
FAQsHow can I test a master cylinder to see if it's bypassing?
FAQsWhat causes the car to pull to one side during braking?
FAQsOne side of my front brakes won’t release, why?
Features and BenefitsPiston assemblies are height-gauged to ensure the master cylinder equals the O.E. unit performance.
Features and BenefitsBleeding kits are supplied with the unit to make the bleeding process faster and easier (where applicable).
Features and BenefitsCast-iron master cylinders feature a premium protective coating to minimize rust and extend unit life.
Features and BenefitsOnly new O.E.-quality seals and cups are used in the remanufacturing process to ensure O.E. performance and reliability. All rubber components meet S.A.E. specifications.
Features and BenefitsBores meet critical micro-finish specifications to eliminate pitting and corrosion, a cause of premature failure.
Features and BenefitsAs a remanufactured Original Equipment part, this unit guarantees a perfect vehicle fit.
Features and BenefitsOur remanufacturing process is earth-friendly, as it reduces the energy and raw material needed to make a new part by 80%.
Features and BenefitsPlastic reservoirs are vacuum-tested to ensure they are leak free.
Hazardous MaterialNo
Height - Each (Inch)9.5
Installation Hardware IncludedNo
Item Level GTIN00082617004442
Length - Each (Inch)5.5
Life Cycle StatusAvailable to Order
Life Cycle Status DescriptionAvailable to Order - Part is released to customers for ordering.
Master Cylinder Color/FinishGray
Master Cylinder MaterialCast Iron
Mounting Hole Quantity2
Package ContentsMaster Cylinder
Port Quantity2
Primary Port Size3/8 x 24
Product ConditionRemanufactured
Quantity Per Application1
Reservoir IncludedYes
Reservoir MaterialCast Iron
Reservoir TypeIntegral
Secondary Port Size1/2 x 20
Weight - Each (Gross Pounds)6.83
Width - Each (Inch)4.625
Buy Part Now
Top