Cardone Reman 10-1323M Brake Master Cylinder

Buy Part Now

ShowMeTheParts has a wide selection of Cardone Reman products for a variety of years, makes, and models.

Cardone Reman 10-1323M Brake Master Cylinder

BUYERS GUIDE

MakeModelYearEngine
CHRYSLERNEW YORKER70-67All
CHRYSLERNEWPORT70-67All
CHRYSLERTOWN & COUNTRY70-67All
DODGEA10070-67All
DODGEA100 PICKUP70-67All
DODGEA100 TRUCK70-67All
DODGEA108 VAN70-67All
DODGEB100 VAN73-71All
DODGEB200 VAN73-71All
DODGECHALLENGER1970All
DODGECHARGER70-67All
DODGECORONET70-67All
DODGED100 PICKUP71-68All
DODGED200 PICKUP1969All
DODGEDART70-67All
DODGEMONACO70-67All
DODGEPOLARA70-67All
DODGEW100 PICKUP71-69All
DODGEW100 PICKUP74-73All
PLYMOUTHBARRACUDA1970All
PLYMOUTHBELVEDERE70-67All
PLYMOUTHCUDA1970All
PLYMOUTHDUSTER1970All
PLYMOUTHFURY70-67All
PLYMOUTHFURY I70-68All
PLYMOUTHFURY II70-68All
PLYMOUTHFURY III70-68All
PLYMOUTHGTX70-67All
PLYMOUTHROAD RUNNER70-68All
PLYMOUTHSATELLITE70-67All
PLYMOUTHVALIANT70-67All
PLYMOUTHVIP1967All

PART INFORMATION

Brand:Cardone Reman 10-1323M Brake Master Cylinder
Part Number:10-1323M
Part Type: Brake Master Cylinder
Comment:CARDONE Remanufactured Master Cylinders are re-engineered, built and tested to match O.E. performance. Each unit features new, O.E.-quality seals and cups to ensure leak-free, long-lasting performance. Cast-iron master cylinders are treated with a premium protective coating to minimize rust and extend product life. All units are 100% computer tested to ensure perfect fit and function.

PARTS ATTRIBUTES

NameValue
Bore Diameter (N)1.00
E-WasteNo
FAQsThis is caused by a problem with the caliper or a brake hose.
FAQsWhat causes the brakes to lock up after only a couple of miles?
FAQsOne side of my front brakes won’t release, why?
FAQsSimply plug the master cylinder ports and press the brake pedal. If the master cylinder is bypassing, the pedal will go down. If the pedal stops hard, the master cylinder is OK.
FAQsDot 3 and 4 are Glycol-based fluids and Dot 5 is a silicone-based fluid.
FAQsWhat’s the difference between Dot 3, 4 and 5?
FAQsAs a rule, always use the brake fluid recommended by the O.E. which is stamped on the master cylinder lid. Note: Always use new fluid from a sealed container.
FAQsHow can I test a master cylinder to see if it's bypassing?
FAQsWhy is the piston stuck inside the bore of my master cylinder?
FAQsMy original master cylinder leaked out of the back of the piston into the booster area. Why?
FAQsWhat causes the car to pull to one side during braking?
FAQsI replaced the master cylinder and now the pedal is high and hard. Why?
FAQsThe brake pedal is low and spongy. Is it a bad master cylinder?
FAQsWhat type of fluid should I use: DOT 3, DOT 4 or DOT 5?
FAQsCheck the steering and suspension. Inspect both calipers for binding or sticky slides or pins. Check brake lining for oil/grease or uneven wear. Inspect brake hoses for restriction. Check for proper tire pressure.
FAQsCheck booster for a defective push rod seal. If this seal is bad, it could drain the brake fluid out of the master cylinder.
FAQsDoes a step bore style master cylinder require a specific bleeding process?
FAQsThe master cylinder is working correctly. Check for a faulty brake booster or frozen wheel cylinder/caliper.
Features and BenefitsOnly new O.E.-quality seals and cups are used in the remanufacturing process to ensure O.E. performance and reliability. All rubber components meet S.A.E. specifications.
Features and BenefitsPlastic reservoirs are vacuum-tested to ensure they are leak free.
Features and BenefitsPiston assemblies are height-gauged to ensure the master cylinder equals the O.E. unit performance.
Features and BenefitsBleeding kits are supplied with the unit to make the bleeding process faster and easier (where applicable).
Features and BenefitsAs a remanufactured Original Equipment part, this unit guarantees a perfect vehicle fit.
Features and BenefitsBores meet critical micro-finish specifications to eliminate pitting and corrosion, a cause of premature failure.
Features and BenefitsOur remanufacturing process is earth-friendly, as it reduces the energy and raw material needed to make a new part by 80%.
Features and BenefitsCast-iron master cylinders feature a premium protective coating to minimize rust and extend unit life.
Hazardous MaterialNo
Height - Each (Inch)9.5
Installation Hardware IncludedNo
Item Level GTIN00082617558655
Length - Each (Inch)5.5
Life Cycle StatusAvailable to Order
Life Cycle Status DescriptionAvailable to Order - Part is released to customers for ordering.
Master Cylinder Color/FinishGray
Master Cylinder MaterialCast Iron
Mounting Hole Quantity4
Package ContentsMaster Cylinder
Port Quantity2
Primary Port Size1/2 x 20
Product ConditionRemanufactured
Quantity Per Application1
Reservoir IncludedYes
Reservoir MaterialCast Iron
Reservoir TypeIntegral
Secondary Port Size9/16 x 20
Weight - Each (Gross Pounds)6.4
Width - Each (Inch)4.625
Buy Part Now
Top