American Grease Stick (AGS) CNB-312 Brake Hydraulic Line

Buy Part Now

ShowMeTheParts has a wide selection of American Grease Stick (AGS) products for a variety of years, makes, and models.

American Grease Stick (AGS) CNB-312 Brake Hydraulic Line

BUYERS GUIDE

Make Model Year Engine

PART INFORMATION

Brand:American Grease Stick (AGS) CNB-312 Brake Hydraulic Line
Part Number:CNB-312
Part Type: Brake Hydraulic Line
Comment:BRITISH LINE - ISO BUBBLE FLARE AGS is the industry leader in the automotive aftermarket for steel brake, fuel, and transmission lines. Combining only the highest quality components, AGS manufactures steel lines that lead the automotive aftermarket in quality, coverage, and fill-rate. NiCopp is a nickel-copper alloy brake tubing that meets SAE Standard J1047 and ISO 4038; meeting all international and U.S. requirements for brake tubing. This alloy is approximately 9.2 Percent nickel, 1.4 Percent iron, 0.8 Percent manganese, and 88.6 Percent copper. Under the UNS system, this alloy is designated as UNS C70600. NiCopp therefore has the strength and structural integrity of steel lines but with the added benefit of being much more corrosion resistant. NiCopp is also easier to bend and form than steel tubing. Nickel-copper, commonly referred to as 90-10 copper, has been used on several European vehicle brake systems since the 1970's, including: Volvo, Audi, Porsche, and Aston Martin. NiCopp has been used on hydraulic/fluid transfer systems on vehicles where steel lines and tubing are commonly used. This includes brake, fuel and transmission systems. NiCopp is considered the super-premium brand in brake lines and should be considered where the underbody of the vehicle is subjected to the harshest environments, where the longest life-span for lines is required, and/or where direct OEM replacement is desired. - NiCopp Does Not Rust or Corrode - DOT Approved for Hydraulic Brake Systems - Bends 58 Percent Easier than Steel Tubing - Available in Coils of 25ft, 50ft, and 100ft - Finished Lines Available for Domestic Import - Black Oxide Fittings 2X Corrosion Resistance. NiCopp lines and tubing meet the following specifications: SAEJ1047, ISO 4038, AEJ1650, DIN 74234, BS2871

PARTS ATTRIBUTES

Name Value
Bending MethodTubing Bender Not Required
California Prop 653/8 - 24
California Proposition 65WARNING Cancer and Reproductive Harm - www.P65Warnings.ca.gov
End 1 GenderTubing Bender Not Required
FinishBlack Anodized
Fitting Type End 1Bubble
Fitting Type End 1No
Fitting Type End 2Bubble
Fitting Type End 25
Fittings IncludedYes
Flare Type3/8 - 24
Hazardous MaterialBubble
Hazardous MaterialNo
Height - Case (Inch)2.0000
Height - Each (Inch)0.4880
Item Level GTIN00077146380853
Length12 Inches
Length1 Foot
Length - Case (Inch)13.5000
Length - Each (Inch)12.0000
Life Cycle Status DescriptionAvailable to Order - Part is released to customers for ordering.
MaterialNickel - Copper
Quantity Per Application1
Shelf QtyWARNING Cancer and Reproductive Harm - www.P65Warnings.ca.gov
Thread Size End 1 (in)3/8 - 24
Thread Size End 1 (mm)3/8 - 24
Thread Size End 1 (mm)Brake Line
Thread Size End 2 (in)3/8 - 24
Thread Size End 2 (mm)3/8 - 24
Tube Outside Diameter (in)0.188 Inch
Tube Outside Diameter (mm)5 mm
Weight - Case (Gross Pounds)0.5460
Weight - Each (Gross Pounds)0.0840
Width - Case (Inch)2.0000
Width - Each (Inch)0.4880
Buy Part Now
Top