American Grease Stick (AGS) CN-572 Brake Hydraulic Line

Buy Part Now

ShowMeTheParts has a wide selection of American Grease Stick (AGS) products for a variety of years, makes, and models.

American Grease Stick (AGS) CN-572 Brake Hydraulic Line

BUYERS GUIDE

Make Model Year Engine

PART INFORMATION

Brand:Brake Hydraulic Line by American Grease Stick (AGS) | ShowMeTheParts.com
Part Number:cn572
Part Type: Brake Hydraulic Line
Comment:AGS is the industry leader in the automotive aftermarket for steel brake, fuel, and transmission lines. Combining only the highest quality components, AGS manufactures steel lines that lead the automotive aftermarket in quality, coverage, and fill-rate. NiCopp is a nickel-copper alloy brake tubing that meets SAE Standard J1047 and ISO 4038; meeting all international and U.S. requirements for brake tubing. This alloy is approximately 9.2 Percent nickel, 1.4 Percent iron, 0.8 Percent manganese, and 88.6 Percent copper. Under the UNS system, this alloy is designated as UNS C70600. NiCopp therefore has the strength and structural integrity of steel lines but with the added benefit of being much more corrosion resistant. NiCopp is also easier to bend and form than steel tubing. Nickel-copper, commonly referred to as 90-10 copper, has been used on several European vehicle brake systems since the 1970's, including: Volvo, Audi, Porsche, and Aston Martin. NiCopp has been used on hydraulic/fluid transfer systems on vehicles where steel lines and tubing are commonly used. This includes brake, fuel and transmission systems. NiCopp is considered the super-premium brand in brake lines and should be considered where the underbody of the vehicle is subjected to the harshest environments, where the longest life-span for lines is required, and/or where direct OEM replacement is desired. - NiCopp Does Not Rust or Corrode - DOT Approved for Hydraulic Brake Systems - Bends 58 Percent Easier than Steel Tubing - Available in Coils of 25ft, 50ft, and 100ft - Finished Lines Available for Domestic and Import - Black Oxide Fittings 2X Corrosion Resistance. NiCopp lines and tubing meet the following specifications: SAEJ1047, ISO 4038, SAEJ1650, DIN 74234, BS2871

PARTS ATTRIBUTES

Name Value
Bend Angle (deg)Inverted
Bend Angle (deg)1/2 - 20
Bending MethodTubing Bender Suggested
California Proposition 65WARNING Cancer and Reproductive Harm - www.P65Warnings.ca.gov
End 1 GenderTubing Bender Suggested
End 1 Thread Diameter (Inch)1/2 - 20
End 2 Thread Diameter (Inch)Inverted
End 2 Thread Diameter (Inch)1/2 - 20
End 2 Thread Size1/2 - 20
End 3 Thread Size72 Inches
Fitting FinishBlack Anodized
Fitting Type End 1No
Fitting Type End 25
Fittings IncludedYes
Hazardous MaterialNo
Height - Case (Inch)2.0000
Height - Each (Inch)0.5550
Item Level GTIN00077146380686
Length - Case (Inch)73.5000
Length - Each (Inch)72.0000
Life Cycle Status DescriptionAvailable to Order - Part is released to customers for ordering.
Line Length (Inch)72 Inches
Line MaterialNickel - Copper
Quantity Per Application1
Shelf QtyWARNING Cancer and Reproductive Harm - www.P65Warnings.ca.gov
Thread Size End 1 (mm)Brake Line
Weight - Case (Gross Pounds)3.4260
Weight - Each (Gross Pounds)0.5590
Width - Case (Inch)2.0000
Width - Each (Inch)0.5550
Buy Part Now
Top